-
Comes with 91207-004-0000 O-Ring 88 x 2.8 and 22158-004-0000 Impaction External Thread Ring Nut -
This is for Wide Body Width Approx. 60" wide. (Measured outside of tires) The Standard Body has width of Approx. 54" This is for approx. 2013ish-2024 including the HiSun, MSU, Coleman, Big Muddy, Super Mach, Q-Link, and the newest AXIS Models. -
This is for Wide Body Width Approx. 60" wide. (Measured outside of tires) The Standard Body has width of Approx. 54" This is for approx. 2013ish-2024 including the HiSun, MSU, Coleman, Big Muddy, Super Mach, Q-Link, and the newest AXIS Models. -
ODES Left Headlight Complete as Shown
ODES 800 - 1000 UTV
Raider and Ravager
This is for 13209060031
Please Study the Part Pictures
-
ODES Left Headlight Complete as Shown
ODES 800 - 1000 UTV
Raider and Ravager
This is for 13209060031
Please Study the Part Pictures
-
This U-Joint or Cross Shaft Fork has 25mm O.D. End Bearing Caps and is 64mm Wide.
-
ODES Speed Controller 2-plug Connector with 2-Wire
This is for 10109360001
others below;
*Only 1 Plug Limiter Box = 10909360001*
**2-Plug Limiter with 1-wire = 10109360000**
-
Out of stock
Factory HiSun FLYWHEEL (Magneto) PULLER 28mm
FITS MOST ATV - UTV 250 MODELS 2015-2024
We Now List Many HiSun Special Tools !
This PULLER is needed to Replace or Remove the Flywheel
-
This is normally used to Guarantee a special order, like complete Engines or large orders.
The purchaser will receive a receipt of the Item's Cost and Deposit given once this is paid.
-
This is the 450, 500 Rear Drive Shaft that connects the Engine to the Rear Diff. Approx. 5" long. Splined Ends Measure; 24.3mm O.D and 34.8mm O.D. -
HiSun ECU/ECM Controller
HiSun ECU/ECM Controller
For 'EFI' UTV MODELS 500 & 550
2011 - 2023
This has the Modified Chip Set with No Restrictions of
Seat Belts, 4x4, Reverse & adds 500 RPM
These ECUs were used and sent to Delphi to be Reprogramed with the Limits Removed.
Only $100, normally $205
This is the Only ECU that comes with a 6 month Warranty !
-
HiSun Fender Flare for Cargo Bed
Rear Right
For Bench Seat UTVs
THIS IS A FACTORY HISUN PART !
HiSun 2015 - 2024
UTV'S, HiSun SECTOR 500-550-700-750
Massimo KNIGHT 500 - 7000
Bennche COWBOY 500 - 700
Coleman OUTFITTER 550 - 750
Many More Models with Bench Seat *Not Vector Series*
-
HiSun Fender Flare for Cargo Bed
Rear Left
For Bench Seat UTVs
THIS IS A FACTORY HISUN PART !
HiSun 2015 - 2024
UTV'S, HiSun SECTOR 500-550-700-750
Massimo KNIGHT 500 - 7000
Bennche COWBOY 500 - 700
Coleman OUTFITTER 550 - 750
Many More Models with Bench Seat *Not Vector Series*
-
This is normally found behind the Starter Clutch Ring Gear. 25.3mm I.D. x 39mm O.D. x 1.0 m. The newer 1:7 Cranks need the 27mmI.D. washer. -
Fits Oval Mufflers approx. 2015-2019ish, then went to round mufflers. -
This is the the Spigot type (Round Tube both Ends) most common.
We also Have the Flange type Throttle Body for the Odes 650 Comrade.
-
Factory XF3 1000 Transmission / Rear Diff from ODES
This also includes the
Angle Rotation Sensor & Speed Sensor
This Transmission is ready to Bolt In and Go !
MXU1000, Workcross and others.
V-Twin by ODES
PLEASE CONTACT US WITH ANY QUESTIONS OR CONCERNS REGARDING YOUR UTV.
Remember the 1000 Transmissions can fail because the clutch system is worn
and allowing the CVT belt to turn at idle, making shifting hard and jumps in gear.
Just make sure the Belt is Not Turning at idle before you install the belt cover.
-
Used in HiSun 700 Cylinder body (not 750). This 115mm Hardened Bolt is 7mm longer, other Head Bolt is 108.5mm, (2) ea./Cylinder. Each Bolt comes with a New Copper Washer.
