This is a Hard to find part. Fits Valve Rockers for the 800 - 1000 V-Twin.
-
This is for the ODES Disc Mounting Shoulder Bolts sold as a pack of (4) Bolts for 1 Disc. -
This can be use for Camshafts and Transmission Bearings -
10 x 1.25 x 22mm Most Common, comes with 2 Copper Washers
Some Models use the finer Thread 10x1.0, let us know if. needed instead -
Commonly Used on Banjo Bolts -
Add this to both Front and Rear Diff Vent Hoses, no clamps required. -
Out of stock
Factory HiSun FLYWHEEL (Magneto) PULLER 28mm
FITS MOST ATV - UTV 250 MODELS 2015-2024
We Now List Many HiSun Special Tools !
This PULLER is needed to Replace or Remove the Flywheel
-
Factory HiSun FLYWHEEL (Magneto) PULLER 38mm
FITS MOST ATV - UTV 800 and 1000 'V-Twin' MODELS 2008-2024
We Now List Many HiSun Special Tools !
* Now Fits most 2019 and Newer HiSun 550, 700 and 750 *
This PULLER is needed to Replace or Remove the Flywheel
ODES & HiSUN 800 and 1000 ATVs and UTV'S INCLUDING,
MASSIMO, BENNCHE, HISUN, Dominator (and many more)
-
'Front Wheel / Axle Bearing Kit'
Both Bearings and Both Seals for (1) Wheel !
(we also have the Front and Rear Knuckle, if needed)
****** and most other parts ! ******
WILL FIT HISUN and ODES UTVs CARB & EFI MODELS 400,500,700 & 800cc
-
Fuel Filter or Gas Filter
Updated to Fit all Models using Standard Size Fitting of 8.5mm (.325")
FITS EFI MODELS
Fits Most Odes 800, 1000 UTV'S
For ODES and HiSun
-
Fits Front and Rear
-
We now offer this in a USB 'Flash has more Knowledge than most Dealers even know of !
Includes the Can-Am 800 Factory Manual that is what ODES Copied.
-
Fits Front and Rear HiSun Axles 450-1000.
Fits Odes Rear Axles (Odes Front are 22mm)
The Inside Diameter is approx. 22.5
-
This D-Shaped Intake Manifold O'Ring fit both Hisun and Odes 800 & 1000 V-Twins. -
This set of O'Rings is specially to fit the Injectors from all HiSun and Odes Models !
-
We also have the Clutch cover 3 piece Bolt with Washer and Rubber Seal if needed. 21040302201 -
Front Wheel Hub
Also known as Mounting Seat Front Hub
Complete with 4 Wheel Studs as Shown
*Fits ODES 800-1000 with 10mm Studs*
2011 - 2023ish
Stud Pattern #1 to #3 = 110mm (Known as 4x110)
Disc Bolt Pattern #1 to #3 = 88mm
-
Rear Wheel Hub
Also known as Mounting Seat Rear Hub
2011-2013ish had 26mm Splines for the Axles and Hubs.
Now updated to 28mm Splines, 26mm are discontinued and N/A.
Complete with (4) 10mm x 1.5 Wheel Studs as Shown
Fits ODES 800 UTV Early Model Dominator
2011 - 2023ish
Stud Pattern #1 to #3 = 110mm (Known as 4x110)
Disc Bolt Pattern #1 to #3 = 100mm
-
This is the Left side Handlebar Switch for the for the Odes ATV.
-
This Cable is fo the Odes ATV 800 & 1000 called the ASSAILANT. Please Measure your old cable and check the Ends to match. Overall Length is Approx. 49″ and the outer cable sheathing/housing is approx. 45″ (including adjusters) -
These are Rear Pads for many different Manufactures for the Single Piston Calipers. Appelstone, Massimo and more.
